Get FilamentPilot for free: the Free version right away or try Workshop for 30 days
To the machbar 3D main site
Free · Windows 10 / 11 · Mac and Linux

Get FilamentPilot
for free

Two ways, both free: start right away with the Free version, no email needed. Or try the full Workshop licence for 30 days; we'll send you the key by email.

Which system is it for?

No email

Free version: start right away

No email, no account. Free for good.

  • âś“ PLA, PETG and TPU
  • âś“ up to 15 filaments
  • âś“ never expires
Download the Free version for Windows

You can get the trial key here any time later.

Windows warns during installation? How to continue ↓

Included

  • âś“ Import from your slicer and write into every slicer
  • âś“ Import manufacturer profiles and bring them into every slicer, for any material
  • âś“ Printers, stock and calibration

All features

Try the Workshop licence for 30 days

All features, all materials. We'll send you the key by email.

  • âś“ all materials
  • âś“ unlimited filaments
  • âś“ 5 PCs on your network

After clicking, the download for Windows starts and your trial key arrives by email. After the trial the program keeps running as the Free version. Your data stays.

Windows shows a blue warning? That is normal.

FilamentPilot is digitally signed, publisher machbar 3D. Windows still warns about every program it has not seen often yet. This happens with almost any new software from small makers. The warning fades with every download.

How to continue:

Windows protected your PC

Microsoft Defender SmartScreen prevented an unrecognized app from starting. Running this app might put your PC at risk.

More info 1

Don't run
1 · Click “More info”.

Windows protected your PC

App: FilamentPilot-Setup.exe

Publisher: machbar 3D

Run anyway 2 Don't run
2 · Check publisher machbar 3D, then click “Run anyway”.

Simplified illustration. Looks slightly different depending on your Windows version.

  • Your browser warns during the download? Message “not commonly downloaded”: choose “Keep” via the three dots or the arrow (Edge and Chrome).
  • It says “Unknown publisher”? Then the file is not from us. Don't run it, and write to filamentpilot@machbar3d.com.
  • This only happens during installation. Updates from inside the app run without a warning.

First version

Mac and Linux

Same version as Windows, one licence on every system. Download above: choose your system, then the Free version or the trial key. Installation, licence and start are tested on real machines. Transfer to the slicer has not yet been tested there in practice: please back up your slicer profiles first.

How to install

Mac

  1. Open the DMG and drag Filament-Pilot into Applications.
  2. The app is not yet signed by Apple, so the Mac blocks the first start: close the message with “Done”.
  3. System Settings → Privacy & Security → “Open Anyway” for Filament-Pilot.
  4. If macOS says the app is damaged: run xattr -cr /Applications/Filament-Pilot.app in Terminal and open the app again.

Linux

  1. Make the file executable: chmod +x FilamentPilot-Linux.AppImage, then start it.
  2. Message about FUSE? sudo apt install libfuse2t64 (Ubuntu 24.04 and newer) or libfuse2 (Ubuntu 22.04).
  3. Slicers installed via Flatpak are detected.

Updates on Mac and Linux are manual for now. Install new versions by hand. Something not working? Write to us via the contact page.

Good to know

  • Your trial key unlocks the full Workshop licence for 30 days; after that the program keeps running as the Free version — your data stays intact.
  • Cancelled the download or entered your email again? No problem — you'll get the same key sent again, no duplicate sign-up is created.
  • Already a customer and misplaced your key? In the "misplaced your key?" box you can have your existing key sent to you again — whether it's a trial or a purchased licence.
  • FilamentPilot is under active development; you may occasionally run into bugs or unfinished features.
  • We recommend backing up important data separately as well.
  • Your feedback is very welcome — write to us at filamentpilot@machbar3d.com.

Already a customer – misplaced your key?

Trial or purchased licence — either way: enter your email address and we'll send your existing licence key again, only to that exact address.

Operating system
Windows 10 / 11 (64-bit) · Mac · Linux
Storage
approx. 300 MB
Internet
Only needed to activate
Version
…

New in 2.5.1

Getting started videos

Six short videos, about 7 minutes in total, take you from the first start to the sync with your slicer. They ship with the app and play offline: Help → “Getting started: 6 short videos”. Also: OrcaSlicer 2.5 is read and written, current settings of Bambu Studio 2.9.1, OrcaSlicer 2.5.0 and PrusaSlicer 2.9.7, new technical base with current security updates, confirmation before unsaved changes are lost, English interface complete.

More on features and pricing: FilamentPilot at a glance.